Helicopter

A helicopter is an aircraft which is lifted and propelled by one or more horizontal rotors (propellers). Helicopters are classified as rotary-wing aircraft to distinguish them from conventional fixed-wing aircraft. The word helicopter is derived from the Greek words helix (spiral) and pteron (wing). The engine-driven helicopter was invented by the Slovak inventor Jan Bahyl. The first stable, fully-controllable helicopter placed in production was invented by Igor Sikorsky.

Controlling flight

Useful flight requires that an aircraft be controlled in all three dimensions (see flight dynamics). In a fixed-wing aircraft, this is easy: small movable surfaces are adjusted to change the aircraft's shape so that the air rushing past pushes it in the desired direction. In a helicopter, however, there often isn't enough airspeed for this method to be practical.

~ ~ ~ ~ ~ ~ ~ ~ ~ ~

For rotation about the vertical axis (yaw) the anti-torque system is used. Varying the pitch of the tail rotor alters the sideways thrust produced. Dual-rotor helicopters have a differential between the two rotor transmissions that can be adjusted by an electric or hydraulic motor to transmit differential torque and thus turn the helicopter. Yaw controls are usually operated with anti-torque pedals, on the floor in the same place as a fixed-wing aircraft's rudder pedals.

~ ~ ~ ~ ~ ~ ~ ~ ~ ~

For pitch (tilting forward and back) or roll (tilting sideways) the angle of attack of the main rotor blades is altered or cycled during the rotation creating a differential of lift at different points of the rotary wing. More lift at the rear of the rotary wing will cause the aircraft to pitch forward, a increase on the left will cause a roll to the right and so on.

~ ~ ~ ~ ~ ~ ~ ~ ~ ~

Helicopters maneuver with three flight controls besides the pedals. The collective pitch control lever controls the collective pitch, or angle of attack, of the helicopter blades altogether, that is, equally throughout the 360 degree plane-of-rotation of the main rotor system. When the angle of attack is increased, the blade produces more lift. The collective control is usually a lever at the pilot's left side, near his leg. Simultanously increasing the collective and adding power with the throttle causes a helicopter to rise.

~ ~ ~ ~ ~ ~ ~ ~ ~ ~

The throttle controls the absolute power produced by the engine that is connected to the rotor by a transmission. The throttle control is a twist grip on the collective control. RPM control is critical to proper operation for several reasons. Helicopter rotors are designed to operate at a specific RPM. If the RPM is too low, rapid descent with power, known as settling with power could result. If the RPM is too high, damage to the main rotor hub from excessive forces could result. In general, RPM must be maintained within a tight tolerance, usually a few percent. In many piston-powered helicopters, the pilot must manage the engine and rotor RPM. The pilot manipulates the throttle to maintain rotor RPM and therefore regulates the effect of drag on the rotor system. Turbine engined helicopters, and some piston helicopters, use servo-feedback loop in their engine controls to maintain rotor RPM and relieves the pilot of routine responsibility for that task.

Related Topics:
RPM - Settling with power - Piston - Servo

~ ~ ~ ~ ~ ~ ~ ~ ~ ~

The cyclic changes the pitch of the blades cyclically, causing the lift to vary across the plane of the rotor disk. This variation in lift causes the rotor disk to tilt, and the helicopter to move during hover flight or change attitude in forward flight. The cyclic is similar to a joystick and is usually positioned in front of the pilot. The cyclic controls the angle of the stationary section of the swashplate, which in turn controls the angle of the rotating section of the swashplate. The rotating section rotates with the rotor and is connected to blade pitch horns through pitch links, one link for each blade. When the swashplate is not tilted, the blades are all at the collective angle. When it is tilted, the links give a pitch-up at some azimuthal angle and a pitch-down at the opposite angle, hence creating a sinusoidal variation in blade angle of attack. This causes the helicopter to tilt in the same direction as the cyclic. If the pilot pushes the cyclic forward, then the helicopter tilts forward, and the rotor produces a thrust in the forward direction.

Related Topics:
Swashplate - Sinusoidal - Angle of attack

~ ~ ~ ~ ~ ~ ~ ~ ~ ~

As a helicopter moves forward, the rotor blades on one side move at rotor tip speed plus the aircraft speed and is called the advancing blade. As the blade swings to the other side of the helicopter, it moves at rotor tip speed minus aircraft speed and is called the retreating blade. To compensate for the added lift on the advancing blade and the decreased lift on the retreating blade, the angle of attack of the blades is regulated as the blade spins around the helicopter. The angle of attack is increased on the retreating blade to produce more lift, compensating for the slower airspeed over the blade. And the angle of attack is decreased on the advancing blade to produce less lift, compensating for the faster airspeed over the blade.

~ ~ ~ ~ ~ ~ ~ ~ ~ ~

If the angle of attack of any wing, including rotor blades, is too high, the airflow above the wing separates causing instant loss of lift and increase in drag. This condition is called aerodynamic stall. On a helicopter, this can happen in any of three ways.

Related Topics:
Angle of attack - Drag - Stall

~ ~ ~ ~ ~ ~ ~ ~ ~ ~

• As helicopter speed increases, the advancing blades approach the speed of sound and generate shock waves that disrupt the airflow over the blade causing loss of lift.
• As helicopter speeds increase, the retreating blade experiences lower relative airspeeds and the controls compensate with higher angle of attack. With a low enough relative airspeed and a high enough angle of attack, aerodynamic stall is inevitable. This is called retreating blade stall.
• Any low rotor RPM flight condition accompanied by increasing collective pitch application will cause aerodynamic stall.

Helicopters are powered aircraft, but they can still fly without power by using the momentum in the rotors and using downward motion to force air through the rotors. The main rotor act like a "windmill" and turn. This technique is known as autorotation. A transmission connects the main rotor to the tail rotor so that all flight controls are available after engine failure. Autorotation can allow a pilot to make an emergency landing if the engine failure occurs while the helicopter is traveling high enough or fast enough. (see Height-velocity diagram).

Related Topics:
Autorotation - Height-velocity diagram

~ ~ ~ ~ ~ ~ ~ ~ ~ ~

A very peculiar feature of the cyclic is that the lift is made to occur 90 degrees of rotation before the direction of tilt. This is because when one tries to tilt a spinning object (like a rotor), it moves at right angles to the direction of the force. This is called "gyroscopic precession". So control forces on the rotor are rotated 90 degrees before the desired motion. For example, forward motion requires less lift at the front of the disk and more lift at the rear of the disk, so the pilot pushes the cyclic forward. The helicopter's control linkages rotate the pitching forces 90 degrees backwards against the rotor spin, to push on the sides of the rotor rather than its front and back.

Related Topics:
Gyroscopic - Precession

~ ~ ~ ~ ~ ~ ~ ~ ~ ~

It took inventors many years to recognize precession, and to learn how to arrange the cyclic's control system to overcome it.

~ ~ ~ ~ ~ ~ ~ ~ ~ ~