Chair

:For other uses of the term chair, please see chair (disambiguation).

Design and ergonomics

Chair design considers intended usage, ergonomics (how comfortable it is for the occupant), as well as non-ergonomic functional requirements such as size, stackability, foldability, weight, durability, stain resistance and artistic design. Intended usage determines the desired seating position. "Task chairs", or any chair intended for people to work at a desk or table, including dining chairs, can only recline very slightly; otherwise the occupant is too far away from the desk or table. Dental chairs are necessarily reclined. Easy chairs for watching television or movies are somewhere in between depending on the height of the screen.

~ ~ ~ ~ ~ ~ ~ ~ ~ ~

Ergonomic designs distributes the weight of the occupant to various parts of the body. A seat that is higher results in dangling feet and increased pressure on the underside of the knees ("popliteal fold"). It may also result in no weight on the feet which means more weight elsewhere. A lower seat may shift too much weight to the "seat bones" ("ischial tuberosities").

~ ~ ~ ~ ~ ~ ~ ~ ~ ~

A reclining seat and back will shift weight to the occupant's back. This may be more comfortable for some in reducing weight on the seat area, but may be problematic for others who have bad backs. In general, if the occupant is suppose to sit for a long time, weight needs to be taken off the seat area and thus "easy" chairs intended for long periods of sitting are generally at least slightly reclined. However, reclining may not be suitable for chairs intended for work or eating at table.

~ ~ ~ ~ ~ ~ ~ ~ ~ ~

The back of the chair will support some of the weight of the occupant, reducing the weight on other parts of the body. In general, backrests come in three heights: Lower back backrests support only the lumbar region. Shoulder height backrests support the entire back and shoulders. Headrests support the head as well and are important in vehicles for preventing "whiplash" neck injuries in rear-end collisions where the head is jerked back suddenly. Reclining chairs typically have at least shoulder height backrests to shift weight to the shoulders instead of just the lower back.

~ ~ ~ ~ ~ ~ ~ ~ ~ ~

Some chairs have foot rests. A stool or other simple chair may have a simple straight or curved bar near the bottom for the sitter to place his/her feet on.

~ ~ ~ ~ ~ ~ ~ ~ ~ ~

A kneeling chair adds an additional body part, the knees, to support the weight of the body. A sit-stand chair distributes most of the weight of the occupant to the feet.

~ ~ ~ ~ ~ ~ ~ ~ ~ ~

Many chairs are padded or have cushions. Padding can be on the seat of the chair only, on the seat and back, or also on any arm rests and/or foot rest the chair may have. Padding will not shift the weight to different parts of the body (unless the chair is so soft that the shape is altered). However, padding does distribute the weight by increasing the area of contact between the chair and the body. A hard wood chair feels hard because the contact point between the occupant and the chair is small. The same body weight over a smaller area means greater pressure on that area. Spreading the area reduces the pressure at any given point. In lieu of padding, flexible materials, such as wicker, may be used instead with similar effects of distributing the weight. Since most of the body weight is supported in the back of the seat, padding there should be firmer than the front of the seat which only has the weight of the legs to support. Chairs that have padding that is the same density front and back will feel soft in the back area and hard to the underside of the knees.

~ ~ ~ ~ ~ ~ ~ ~ ~ ~

There may be cases where padding is not desirable. For example, in hot climates, padding with fabric or plastic covers is often uncomfortable against the skin. Where padding is not desirable, contouring may be used instead. A contoured seat pan attempts to distribute weight without padding. By matching the shape of the occupant's buttocks, weight is distributed and pressure at any given point is reduced.

~ ~ ~ ~ ~ ~ ~ ~ ~ ~

Actual chair dimensions are determined by measurements of the human body or anthropometric measurements. Individuals may be measured for a custom chair. Anthropometric statistics may be gathered for mass produced chairs. The two most relevant anthropometric measurement for chair design is the popliteal height and buttock popliteal length.

Related Topics:
Anthropometric - Popliteal height - Buttock popliteal

~ ~ ~ ~ ~ ~ ~ ~ ~ ~

For someone seated, the popliteal height is the distance from the underside of the foot to the underside of the thigh at the knees. It is sometimes called the "stool height". (The term "sitting height" is reserved for the height to the top of the head when seated.) For American men, the median popliteal height is 16.3 inches and for American women it is 15.0 incheshttp://www.cdc.gov/niosh/pot_anth.html. The popliteal height, after adjusting for heels, clothing and other issues is used to determine the height of the chair seat. Mass produced chairs are typically 17 inches high.

~ ~ ~ ~ ~ ~ ~ ~ ~ ~

For someone seated, the buttock popliteal length is the horizontal distance from the back most part of the buttocks to the back of the lower leg. This anthropometric measurement is used to determine the seat depth. Mass produced chairs are typically 38-43 cm deep.

~ ~ ~ ~ ~ ~ ~ ~ ~ ~

Additional anthropometric measurements may be relevant to designing a chair. Hip breadth is used for chair width and armrest width. Elbow rest height is used to determine the height of the armrests. The buttock-knee length is used to determine "leg room" between rows of chairs. "Seat pitch" is the distance between rows of seats. In some airplanes and stadiums the seat pitch is so small that there is sometimes there is no leg room for the average person.

~ ~ ~ ~ ~ ~ ~ ~ ~ ~

For adjustable chairs, the aforementioned principles are applied in adjusting the chair to the individual occupant.

~ ~ ~ ~ ~ ~ ~ ~ ~ ~

Arm rests

A chair may have armrests. Armrests will support part of the body weight through the arms. They further have the function of making entry and exit from the chair easier (but from the side it becomes more difficult). Armrests should support the forearm and not the sensitive elbow area. Hence in some chair designs, the armrest is not continuous to the chair back, but is missing in the elbow area.

~ ~ ~ ~ ~ ~ ~ ~ ~ ~

A couch, bench, or other arrangement of seats next to each other may have arm rest at the sides and/or arm rests in between. The latter may be provided for comfort, but also for privacy e.g. in public transport and other public places, and to prevent lying on the bench or coach. Arm rests prevent or complicate both desired and undesired proximity. A loveseat in particular, has no arm rest in between.

Related Topics:
Couch - Bench - Privacy - Public transport - Public place - Proximity

~ ~ ~ ~ ~ ~ ~ ~ ~ ~

See also seats in movie theaters, and .

~ ~ ~ ~ ~ ~ ~ ~ ~ ~